We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements: Lots of other little improvements such as a polarity protection FET on the power pins and a bit of prototyping area. And the shield is assembled and tested here at Adafruit so all you have to do is solder on straight or stacking headers and the terminal blocks. Lets check out these specs again: 2 connections for 5V 'hobby' servos connected ... [Read More]
Arduino A000079 Motor Shield, R3, 5V to 12V. Operating voltage: 5V to 12V. Motor controller: l298p. Drives 2 dc motors. Arduino A000079 Motor Shield, R3, 5V to 12V. Unit Count : Motor.
Features: 1. to 4 bidirectional DC motors and 4 PWM speed controllers (approximately 0.5% resolution) 2. Up to 2 stepper motor forward and reverse control, single / double step control, staggered or micro-step and rotation angle control 3. 4-way H-bridge: The L293D chip provides 0.6A (peak 1.2A) current per bridge with thermal shutdown protection, 4.5Vto36V 4. The pull-down resistor ensures that the motor remains stopped at power-up 5. Large terminal blocks make wiring easier (10-22AWG) and power 6. With reset button 7. 2 large terminal external power terminals, to ensure logic and motor drive... [Read More]
CNC Shield Board: Latest Arduino CNC Shield Version 3. 0 GRBL 0. 9 compatible 4-Axis support (X, Y, Z , A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis (6 in total) Coolant enable Compatible with A4988 or DRV8825 stepper driver Runs on 12-36V DC Arduino UNO R3 Board: MCU: ATmega328 USB interface: ATmega16U2 Operating voltage: 5V Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 I-I/O pin output current: 40mA max 3. 3V output current: 150mA max Flash memory: 32 kB (0. 5kB used by bootloader - includ... [Read More]
Features : 2 interface for 5V Servo connected to the Arduino"s high-resolution dedicated timer - no jitter. Can drive 4 DC motors or 2 stepper motors or 2 Servo. Up to 4 bi-directional DC motors with individual 8-bit speed selection. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 25V DC. Pull down resistors keep motors disabled during power-up. 2 external terminal power interface, for separate logic/motor supplies. Compatible for A... [Read More]
Introduction When we are doing robot experiments, it needs to use multiple PWM ports to drive the servo motor, however, the common used Arduino UNO R3 only has 6 PWM ports, so it is not enough.This allows you to use this expansion board, which is directly stacked on the Arduino UNO R3 board and can drive up to 16 servos. It uses I2C input, just occupies A4 and A5 of the Arduino UNO R3 board. The expansion board contains PCB double sided holes ,which can direct to solder with components to build up prototyping circuits. Specification 1.I2C input, to control 16-channel PWM output 2.Servo power ... [Read More]
Technical Specifications: 1. Logical part of the input voltage VD: 5V 2. Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input 3. Logical part of the work current Iss:
This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements: Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well. Completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that man... [Read More]
CNC Expansion Board:-GRBL 0.9 compatible-Runs on 12-36V DC -4-Axis support: X, Y, Z-It can drive 4 stepper motors, and each stepper motor only needs 2 IO ports. That is to say, 6 IO ports can manage 3 stepper motors very well, which is very convenient to use.KeeYees UNO R3 Board: -Microcontroller: ATmega328P-Chip: ATmega16U2 -Operating Voltage: 5V-Input Voltage (recommended):7-12V-Input Voltage (limit):6-20V-Flash Memory: 32 KB of which 0.5 KB used by bootloader-Digital I/O Pins: 14 Digital I/O Pins (6 PWM outputs)-Analog Input Pins: 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 m... [Read More]
VNH5019 Dual Motor Driver Shield for Arduino This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board (Arduino MCU sold separately). Its dual robust VNH5019 motor drivers operate from 5.5V to 24V and can deliver 12A continuous (30 A peak) per motor, or a continuous 24A (60 A peak) to a single motor connected to both channels. These drivers offer current-sense feedback and accept ultrasonic PWM frequencies for quieter operation. The Arduino pin mappings can all be modified if the defaults are not compatible with your project, and the motor dri... [Read More]
This controller is able to regulate the speed of one DC motor with Arduino. Cytron 10A Motor Driver Shield (Arduino)"SHIELD-MD10" is a compatible Arduino motor shield for controlling high current brushed DC motor up to 10A continuously. It should be stacked on to an Arduino main controller board such as Arduino UNO R3. Features: Shield for Arduino Speed controller to control one motor. Bi-directional control for 1 brushed DC motor. Support motor voltage ranges from 7V to 30V (Rev2.0). Maximum current up to 10A continuous and 15A peak (10 seconds). 3.3V and 5V logic level input. Solid state ... [Read More]
Manufactured By Atomic Market A monolithic integrated, high voltage, high current, 4-channel driver Size:6.8cm x 5.5cm x 2cm - 2.68inch x 2.17inch x 0.79inch. Tested compatible for Arduino Mega, Diecimila & Duemilanove 2 external terminal power interface, for seperate logic/motor supplies
The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. Operating Voltage 5V to 12V Motor controller L298P, Drives 2 DC motors or 1 stepper motor Max current 2A per channel or 4A max (with external power supply) Current sensing 1.65V/A Free running stop and brake function Click me to konw more Pa... [Read More]
Specification: Chip: L298N Logic voltage: 5V Logic current 0mA-36mA Storage Temperature: -20 ℃ to ℃ to +135 Operating mode: H-bridge driver (dual) Drive voltage: 5V-35V Drive current: 2A (MAX single bridge) Maximum power: 25W Dimensions: 43x43x27mm Package include: 1x L298N Module Note: This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control ... [Read More]
CNC Shield Board: Latest CNC Shield Version 3.0 for arduino. GRBL 0.9 compatible. 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Support 6pcs ends stop for each axis. Coolant enable. Compatible with A4988 or DRV8825 stepper driver. Runs on 12-36V DC. DRV8825 Stepper Motor Driver: Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It's not arduino official board but it's compatible with all arduino software and hardware). Nema 17 Stepper motor Specification: Model No.:17HD48002H-22B Step Angle: 1.8 deg Holdi... [Read More]
2Pcs L298N Dual H-Bridge Stepper Motor Driver Board For ArduinoDescription:Double H bridge driveChip: L298N (ST NEW)Logical voltage: 5VDrive voltage: 5V-35VLogical current: 0mA-36mADrive current: 2A (MAX single bridge)Storage temperature: -20 to +135Max power: 25WWeight: 30gSize: 43
L298P Shield DC motor driver adopts the L298P driver chip wich is exclusively made for large-power motor. It can drive 2 DC motors directly with a drive current reaching 2A. The motor output is equipped
L298P Shield DC motor driver adopts the L298P driver chip wich is exclusively made for large-power motor. It can drive 2 DC motors directly with a drive current reaching 2A. The motor output is equipped
Please note, this item ships from an international seller. Expected delivery is 10-15 days. International ShippingL298P Shield DC motor driver adopts the L298P driver chip wich is exclusively made for large-power motor. It can drive
L298P Shield DC motor driver adopts the L298P driver chip wich is exclusively made for large-power motor. It can drive 2 DC motors directly with a drive current reaching 2A. The motor output is equipped
L298P Shield DC motor driver adopts the L298P driver chip wich is exclusively made for large-power motor. It can drive 2 DC motors directly with a drive current reaching 2A. The motor output is equipped
L298P Shield DC motor driver adopts the L298P driver chip wich is exclusively made for large-power motor. It can drive 2 DC motors directly with a drive current reaching 2A. The motor output is equipped
This expansion board, as drive expansion board, can be used for engraving machines and 3D printers. It totally has four slots and can drive 4 A4988 stepper motors, and each stepper motor only needs two
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com