Caution : the product don't have plastic cover. Please click:http://www.amazon.com/dp/B00A7IZN70 to buy the one with plastic cover Specification Output Power:40W + 40W (8ohm) Frequency Response:10Hz -- 60kHz (±2dB) Signal/Noise Ratio: ≥85dB (A) Load impedance: 8ohm or 4ohm Distortion:≤0.9%(28W) Maximum Power Consumption:220W Sensitivity:≤0.26V Tubes: 6CA7T x 4 12AX7B x 2 12AU7 x 2
This stereo integrated amplifier offers impressive powerful sound. Thanks to its hybrid design (2 x 6P1, 2 x 6N1 vacuum tubes) it provides richness of sound synonymous with pure valve amplification. A built-in headphone output is a perfect choice for those who prefer discrete listening. If someone is looking for a small sound system for a 30sqm room and wants it to be able not only to sound (and look) attractive, but also to be multi-functional.... the choice of ACIN TA-10D seems to be a reasonable and completely legitimate. It offers plenty of features, and also provides a very musically pl... [Read More]
Warm reminder: You should take about 100h time to operate the amp.RUN-IN to the amp gives it's best and stable sound.so during the first 100h use time the sound maybe is not the best,you can also use your own run-in method. Specification: Frequency response: 15Hz-36KHz / (20Hz-30KHz) Harmonic Distortion: ≤ 1.2% (1KHz) Input Sensitivity: 290mV Output power: 35W * 2 (8Ω ) vacuum tube: KT88*4, 12AU7*2, 12AX7*1 Input Impedance: 100K Output Impedance: 4Ω 8Ω Headphone Output Impedance: 32Ω -300Ω Signal-to-noise ratio: 89dB Power supply voltage:110-120V 60Hz/50Hz(+-10%) (For United States)... [Read More]
The amplifier stage is composed of a standard class Class A power amplifier circuit. The amplifier tube to screen load impedance is 6KΩ, and the plate voltage is 375V. Using only the gate negative bias mode, the zero-signal push-pull two-plate electrode power is 85mA, and the large screen current increases to 150mA. Rated output power is 16W, high power can reach 22W. 4.0 Bluetooth HiFi Module The amplifier supports Bluetooth input and can be easily paired with Android, iPhone, iPad, Tablet PC and other devices. Support headphones to switch output, is a tube headphone amp Bluetooth tube ampl... [Read More]
Specifications: Tubes: 6J4 x 2; Bluetooth version: Bluetooth 4.2 support apt-X and apt-X low latency; Headphones output: 16-64ohm; Amplifier Chip: TPA3116; Rated output power: 2*50W /4Ω; Audio input: RCA input + Bluetooth input; Audio output: 1 set of Banana Speaker Jacks; Signal to noise ratio: >99dB; Frequency: 20Hz-20KHz; Dimensions: 5.06*3.86*1.3in; Power supply: DC 24V 4.5A; Packing List: 1 * Power Amplifier 1 * Power supply 2 * 6J4 tube 1 * Bluetooth antenna
.Max. Power Output: 2x25W .Frequency: 20-25kHZ .S/N Ratio: 86dB .Distortion: 0.1% .Input Impedance: 100kΩ .Output Impedance: 4Ω, 8Ω .Max. Power Consumption: 110W .Input: 2.4GHz Wireless Audio Input,USB DAC, LINE .Output: Speaker, Headphone, Stereo Preamp .Voltage: AC100-120V/50-60Hz AC220-240V/50-60Hz .Tubes: 6N1, 6N2, 6E2 .Dimensions: 260x160x155mm (LxWxH) .Weight: 3.8KG
Features: two Japanese high quality EI output transformers with high sound quality Use the EI type power transformer designed specially for this machine The pre-amp stage uses each 2x 12AX7 and 12AU7 vacuum tubes, and the power stage uses 4 EL34 vacuum tubes to be AB1 type push-pull power amplification, providing triode and super-linear selection function. Triode working, sound soft, pure and smooth, suitable for voice, string; super linear way, open, ebullience, sound momentum is good, suitable for large dynamic scenes, appreciation and other types of music. There is a driver tubes and powe... [Read More]
Notice:Both 4Ω and 8Ω speakers can connect to the 8Ω and 0Ω posts of this amplifier. Specifications: Output power: 6.8W * 2 Frequency response: 20Hz-20KHz Input impedance: 100K ohms Output impedance: 4/8Ω SNR: 90db Input Sensitivity: 500mv-2000mv Harmonic distortion: 1% (1KHz) Tube: 5Z4P * 1 6H8C * 2 6P1 * 4 Operating voltage: 110V Weight: about 7 kg Size: 260mm * 215mm(including terminals and knobs 260mm) * 150mm (W*D*H) Package includes: Finished tube amplifier ×1 Power cable ×1
Warm reminder: You should take about 100h time to operate the amp.RUN-IN to the amp gives it's best and stable sound.so during the first 100h use time the sound maybe is not the best,you can also use your own run-in method. Specification: Rated output power: 25W + 25W (RMS Triode) 45W + 45W (RMS Ultralinear) Harmonic distortion: 1% (1kHz) Frequency response: 15Hz ~ 30kHz (-1.5dB) Input Sensitivity: 280mV; 520mV (pre in) Input impedance: 100KΩ Output impedance: 4Ω 8Ω Signal to noise ratio: 92dB Left and right output balance:
Dared I-30 also called I-30HD,it is well-known world-amp, all tube integrated amp output 2x30watts,We are DARED brand authorized seller! World first and only valve (tube) amp with DAC and headphone output. Speaking for class-AB tube amplifiers, there are only three kings of power tubes: EL34, 6L6G and KT88. Of course, if you are audiophile or tubephile or music lover, you probably know the best are the EL34 and 6L6G. It uses simple open class-A circuit with two dual-triode tubes for two stages of Triode-Single-end (SET) for preamp amp and drive stage with little feedback. Dared engineers this ... [Read More]
Notice: Please turn on the amplifier for about 15 seconds before you connect the audio source and put on the headset. We recommend using 24~600Ω headphones, while armature earphones and headphones that have low resistance and high sensitivity are not suitable. As there will be tube Microphone effect, please keep the amplifier steady while using it. For noise issue, please keep it away from devices like routers, mobile phones or something that may interfere in the audio signal. If there are no interference, please remove all input and listen to see if the noise still exists. If so, the device ... [Read More]
Rockville BluTube Bluetooth tube 70 watt amplifier/home theater stereo receiverrockville BluTube audiophile grade tube amplifier with Bluetooth. 25 watts x 2 RMS @ 8 Ohm. 35 Watts x 2 RMS @ 4 Ohm. Tube Amps do not hard-clip even at high volumes and are extremely efficient. Due to this the amp sounds more like double the rated power!.
Input Interface: 3.5 mm Stereo Jack Output Power: 32 Ω: 115mW 64 Ω: 77 mW 150 Ω: 39 mW 300 Ω: 20 mW THD+N: 0.032% SNR: 95dB Consumption Power: 5.5W Frequency Response: 20Hz-20kHz Residual Noise: 0.02mV
FEATURES: Our T2 amp utilizes two 6J9 J-grade tubes and two NJM5532D as core parts of the circuit. The 6J9 tubes amplify the voltage which increases the input signal. The current formed by NJM5532D (Made by JRC Japan Company) amplifies the electric circuit to drive the mini headphone amplifier. These two features provide an awesome combination of high quality sound and a very powerful drive current for an optimum listening experience! Our T2 amp adopts a Single Chip Microcomputer and Relay to control the muted sound when the device is OFF or first turned ON. It allows the device to warm up bef... [Read More]
Note: Power cord is not included. Specifications: Tube: 6AD10 Power Output: 3.5W+3.5W @ 8 ohms Frequency Response: 30-40Khz (+-1db) Input Sensitivity: 500mV Signal-to-Noise Ratio: -80dB / 3.5W Residual Noise < 0.5mV AC Input AC Voltage: 100-250V AC Power Consumption: 38W Input Impedance: 10K ohms Output Impedance: 8/6/4 ohms (Japan Z11-EI48*24 Output Transformers) Dimensions: 160mm (w) x 134mm (d) x 125mm (h) Weight: 2.5kg Input: RCA Jacks Output: Banana Jacks AC: Standard IEC Jack with Fuse protection (2A Fuse) Package: 1PC Black tube amplifier
Notice: Please turn on the amplifier for about 15 seconds before you connect the audio source and put on the headset.We recommend using 24~600Ω headphones, while armature earphones and headphones that have low resistance and
The 7 in. Beast LED drop-in headlight is truly a beast to contend with. 4,000 lumens of pure white light that is concentrated on nothing but the road ahead. The Beast is for the rider
All of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world. This listing is for 1 LED integrated fixture with a T8 LED tube
WAGE WAR ON GRIME Meet the newest weapon in the war on grime: introducing SPX2598 from Sun Joe, with next-generation grime-fighting technology in one powerful, compact portable pressure washer. Packed with 14.5-amps of pure cleaning
Realm electric pressure washer is an ideal way to efficiently clean siding, driveways, cars, patio furniture, and lawn equipment with the power of pressurized water jets. It has the most advanced pump with double sealing
The Camco 30M/30F AMP Circuit Analyzer helps protect your electrical equipment from improperly wired electrical boxes by visually indicating faults before you connect your RV's Power Cord to the electrical box. The 125V Dogbone includes
Torchstar 13 inch Extendable Under Cabinet Lighting, Closet Linkable LED Light Bar, Multi-functional LED Workbench Light, 450lm Integrated T5 Tube, Eye Care 4200K Cool White, Pack of 2✓13 inch extendable LED under-cabinet Light, integrated T5
Under Cabinet 6 Light Fixtures With Black Finish Aluminum Material Integrated 3" 24 Watts.Brand: World of Bright.Category: Under Cabinet.Collection: Adhafera.Finish: Black.Width: 3.25 in.Height: 1.3 in.Depth: 3.25 in.Number Of Bulbs: 6.Bulbs Included: No.Bulb Type: Integrated.Bulb Wattage:
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com