Guitar Wire- Gavitt Single-Conductor Braided Shield Cable, 6 feetBraided shield wire just like the kind used on Gibson guitars. #22 AWG 7/30 tinned soft copper cotton braided push back wire with an overall #34 AWG (2 end) tinned copper braid shield
Guitar Amp Potentiometer. Audio/Log pots are typically used for volume control, and Linear pots are typically used for effects. 100KL / 100K Linear / 100KB / 100,000 ohms. Fits 3/8" Hole. 1/4" Solid Shaft. 24mm Body, Solder Lugs, 1/2 Watt Rated, 300° Rotation, 250VDC Rated, Carbon Composition. Comes With Hex Nut and x2 Washers
Vintage style cloth covered wire. Wire is 22 awg 7-strand and pre-tinned, cloth jacket has a waxed cotton outer braid and a Celanese inner braid. This wire is an accurate replication of the wire used in vintage Fender's. Made by the same company. Stranded wire is the good stuff for wiring or rewiring your guitar. Much easier to work with than solid core when you are trying to solder to the back of a pot, or lug. White is hot, black for ground, yellow was traditionally used for the middle pickup on 3 pickup single coils.
Self-adhesive copper foil tape. Each roll is 6 yards long and 2 inch wide. The tape has Dual conductivity so current will flow through both sides and the adhesive. One side is coated with a strong adhesive which is protected by paper backing on the roll. Tape is resistant to oxidization and discoloration. Suitable for indoor and outdoor use. The tape has a wide variety of uses and will perform perfectly when applied in the following roles: EMI guitar shielding, slug repellent, snail repellent, soldering, stained glass, paper circuits, educational aid, electrical repairs, household repairs,... [Read More]
Dunlop’s Super Pot Potentiometers are high-performance volume/tone pots that are made to last a lifetime. Resistant to dust and corrosion, they provide a smooth audio-style taper that will never sound noisy or scratchy. They’ve been tested at over 7 million turns-after that, we stopped counting. Put a set of these pots in your instrument, and they just may be the last you ever buy.
This kit is a nice step up for your Les Paul from your stock components. The kit contains only name brand parts starting CTS 500K pots, a pair of Orange Drop .022uf/400v caps, a quality Switchcraft switch (includes a deep nut for guitars with carved tops) and jack finish it off. The kit also includes the wire and instructions you'll need to do the job right. Please Note: 1. As a general rule pre-1977 production Les Paul's, many of the historic reissue Les Paul's, ES series, PRS and Hamer guitars use short shaft pots. If you are uncertain whether your guitar uses short (3/8") or long (3/4") sha... [Read More]
This harness is completely prewired, all you need to do is solder your pickups to the switch and ground them to the volume pots Material: Plastic & metal Switch Cap: black LP Wiring Harness 1 Volumes / 2 Tones / 3 way switch 2 x A500k, 1 x B500k Pots with 18mm Shafts, Base Dia: 16mm Package Included: 1 x Wiring Harness for Fender ST SQ guitars (not include in Pickup) Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
This harness is completely prewired, all you need to do is solder your pickups to the switch and ground them to the volume pots. Material: Plastic & metal Switch Cap: Cream LP Wiring Harness 2 Volumes / 2 Tones / 3 way switch 2 x A500k, 2 x B500k Pots with 18mm Shafts, Base Dia: 16mm Package Included: 1 x Wiring Harness for Gibson guitars Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! Any problem you faced about our items, please freely make us know, we will response within 24 hours, and try our best to solve i... [Read More]
100% Brand new,never used Item's color might be different from the picture because of the aberration. Strat Wiring Harness One Volume/Two Tones/5 way switch 2 x A500k,1 x B500k Pots with 15mm Shafts/Base Dia:16mm.047 capacitors Input Jack This harness is completely prewired.All you need to do is solder your pickups to the switch and ground them to the volume pot. Use this harness for Strats and Strat style guitars with 3 pickups Package Included:1set of Wiring Harness-Prewired for Strat Guitar
12 feet genuine GAVITT vintage-style wire for guitar. Includes 6 feet of black wire and 6 feet of vintage white.This vintage cloth push-back wire is 22AWG stranded wire, with textile braid made by Gavitt. This is the same wire used by Fender. It has a tinned overcoat after the individual strands of the conductor are twisted together locking the strands into a single unit just like Fender has their wire made. The benefit to this process is that the wire holds its shape very well without having fraying strands at the cuts needing to be twisted and tinned, making it very easy to work with. The cl... [Read More]
TAOT Deluxe Wiring Kit for Fender Stratocaster w/ Wiring Diagram. Featuring CTS high quality 450G series potentiometers designed specifically for guitars. 1/4" high X 3/8" diameter bushing with vintage taper volume pot with more gradual taper and greater volume control. Pots require 3/8" mounting hole. All parts in the kit are high quality USA sized parts and are not compatible with import guitars using metric sizing.
1 Pair .047uf 200v 715P ORANGE DROP Capacitors 5% Tolerance Polypropylene Great cap for most applications. Well suited for faster styles where a fast pick dynamic is desirable Great for Blues too! Rated at 5% tolerance We sell our caps in Matched Pairs Tested to 5% Tolerance of stated value and of each other Perfect for Humbuckers and Single Coils as well. Choice Capacitors for all applications. Crisp sound with clean harmonic content.
This pot allows you to do wiring modifications to your guitar without having to modify the body of the guitar. Used for coil splitting, coil tapping and phase shifting. This is a short shaft pot (threaded bushing is 3/8" tall & 3/8" diameter, shaft is .236" diameter). Pot is manufactured by Bourns. Note: 1. Requires 3/8" diameter mounting hole 2. If you have an import guitar it is probably using metric sized components and these pots cannot be used without modifying the openings on your guitar
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com