Remember when power tools were actually powerful? Reminiscent of your Grandpa's bandsaw, the WEN 10-Inch Two-Speed Band Saw is the perfect companion for any workshop. With a 3.5-amp motor and a 9-3/4 inch throat, this beast will attack boards with cuts up to six inches deep and 9-3/4 inches wide. Two-speed operation allows for speeds of either 1520 or 2620 FPM. The design of this saw uses 72-inch blades anywhere from 1/8 to 1/2 inches in size for a variety of both intricate and powerful cuts. The spacious work table measures in at 14 x 12-1/2 inches in size and can be swiveled up to 45 degrees... [Read More]
These tires will be running on your band saw long after rubber ones have literally turned to dust. They do not dry out, therefore, they will not crack, peel or harden like rubber tires do. They hold so tightly to the wheel you won't need to glue them down. Place in Hot water for 5-10 minutes before installing. Colored bright orange for easier inspection. Be sure to follow label instructions for best performance & ease of installation. Tires come in pairs. Made in USA.
Black Rubber Motor Drive Belt with 4 Ridges. Replaces Only P/N 1-JL22020003 used on some 10" band Saws. Check your P/N before ordering
3 Urethane tires specifically made for the 10" Craftsman Band Saws Models: 133.244510, 113.244512 & 113.244513
Get all of the features of a full size bandsaw in this bench top model. The large cast iron table, edge facing thrust bearings, a powerful 1/3 HP induction motor, and 4-5/8 in cutting capacity are all of the features you come to expect as standard from Rikon. Add the optional stand for the functionality of a floor model. Specs: 1/3 HP, 3.5 amp motor, speed 2780 ft/min, safety paddle switch. Cutting capacities: Height 4-5/8", Width 9-5/8". Table is 13-3/4" x 12-1/2". Edge facing thrust bearings. 70-1/2" blade range from 1/8" to 1/2".
Remember when you had a saw that was both compact and powerful? The WEN 9-Inch Benchtop Band Saw attacks boards with cuts up to 3-1/2 inches deep and 9 inches wide. The 2.5-amp motor rotates the included 1/4-inch blade at up to 2500 feet per minute. The design of this saw uses 59-1/2 inch blades anywhere from 1/8 to 3/8 inches in width for both intricate and powerful cuts. The spacious work table measures in at 12-1/4 x 11-7/8 inches in size and can be beveled up to 45 degrees. This package includes a miter gauge, an onboard 2-1/2 inch dust port, a fence for creating straight cuts, and an adju... [Read More]
Even under occasional use, the tires on band saw wheels periodically need to be replaced. Carter ULTRA BLUE Urethane Tires are made from the highest quality material to exacting standards. That's why they deliver such outstanding performance and wear consistently for so long. Unlike rubber tires, which are cumbersome to replace, these slip on without any special tools, messy adhesives, or excessive downtime. Simply heat in hot soapy water and stretch the tire on to the wheel and the band saw is ready to use.
These tires will be running on your band saw long after rubber ones have literally turned to dust. They do not dry out, therefore, they will not crack, peel or harden like rubber tires do. They hold so tightly to the wheel you won't need to glue them down. Colored bright orange for easier inspection. Will fit 10" diameter wheels or to plus or minus 1/4". Be sure to follow label instructions for best performance & ease of installation. Tires come in pairs. Made in USA.
These tires will be running on your band saw long after rubber ones have literally turned to dust. They do not dry out, therefore, they will not crack, peel or harden like rubber tires do. They hold so tightly to the wheel you won't need to glue them down. Colored bright orange for easier inspection. Will fit 10" diameter wheels or to plus or minus 1/4". Be sure to follow label instructions for best performance & ease of installation. Tires come in pairs. Made in USA.
Introducing the replacement Band saw Blades by POWERTEC. This high performance blade is designed to provide a reliable cutting action and deliver welds on wood, plastics and non-ferrous metals. Made from high carbon steel, these 70. 5 x 1/4 band saw blades are heat resistant and offer a premium precision cutting user experience. Every weld is for proper tooth spacing, matched set and exact finishing. The band saw blade metal teeth feature an optimal geometric design and have been hardened to RC 64-66. POWERTEC band saw blades stay sharp with a long life and consistent performance. Our blades a... [Read More]
Blade breakage and poor blade performance are common problems with small 2 or 3 tabletop bandsaws. These problems are caused by the extreme flexing of the blade caused by the small size of the wheels that the blade runs on and the high speeds normally used. These 3 wheeler blades are specially designed for 2 or 3 three wheeler tabletop bandsaw to cut wood or non ferrous metals only . 3 wheeler blades will not stand up to ferrous metals. The different type of tooth patterns along with their functions are described below: (The width of blades do not play a role in the type of material being cut)... [Read More]
14" Bandsaw which provides woodworkers with a full 13-5/8" wide and 13" high cutting capacity at an entry level price. The 1-1/2 HP, 115/230 dual volt motor, with two blade speeds of 2,950 or 1,445
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com