Simple and easy to use ar-15 gas block dimple tool. Works with any gas block that uses a 10-32 set screw. We feel that placing a dimple on your barrel is essential in making sure your gas block does not move. When your gas block is aligned properly, use the screw included to hold the gas block in place. At this point you can use the marking pin to locate the hole or simply run a 1/8" drill bit through the center of the screw to make your dimple. Includes: 1- set screw, 10-32, with center hole 1- marking pin instructions.
The Wheeler engineering gas block taper. Fix me features, benefits, Battenfeld technologies Inc. Contact us for any Questions or issues you may have
Also referred to as Roll, Tension and Expansion Pins. Hollow and slotted lengthwise to create tension, these self retaining Spring Pins are made of Type 420 Stainless Steel.Stronger than 18-8 stainless steel, more corrosion resistant than zinc-plated and plain steel. Magnetic. Minimum Rockwell hardness is C43. They are installed by two easy operations, just drill and drive. Useful for many purposes, including electrical connectors in patch board circuits, terminals, fixtures for wire harness, actuators for drum, to secure pulley or gear to shaft, hinges, positioning, studs and many others. Sup... [Read More]
Having the right tool for the job makes any Gunsmithing project so much easier! without the right tool, you may damage fine finishes or break parts. The x-block is the right tool for anyone driving pins out of firearms. It has all the features to get the job done smoothly and professionally. The x-block has both a "V" Slot and a rounded Slot running across the face of the block to support a variety of barrels and slides. The block is made of a tough, non-marring, polymer, and edged with a softer non-slip outer overmold. The block has multiple holes to take on most any project, as well as a mol... [Read More]
Use for fast and safe removal of pins. Drop forged, heat treated steel. Sizes - 1/16" x 2 3/4", 5/64" x 3 1/4", 3/32" x 3 1/2", 1/8" x 4", 5/32" x 4 1/2", 3/16" x 4 3/4", 7/32" x 5", 1/4" x 5 1/2", 5/16" x 6 1/4". Includes roll-up storage pouch.
For firearm assembly and disassembly, the Universal Bench Block is your best friend. It features a variety of notches, grooves, and holes on both sides and is ideally suited for M1911-style pistols. Need to install a pin, detent, or spring? The Universal Bench Block is the answer. 1-5/16" high, 4" in diameter. Non-marring urethane for long use.
Looking for a standard A2 front sight to mount to your rail? Our all aluminum, lighweight front sight is just what you need. Available in either rail height or gas block height it provides a quick, easy solution for adding a front sight to any rifle with a rail.Gas Block Height - If your front rail is on your gas block and lower than the upper rail
Perfect for: Gunsmiths of all skill ranges; Gun owners who are looking to do more detailed work; Gun enthusiasts who are looking to work on all types of guns. Specs: Diameter: 3 3/4"; Thickness: 1 ¼ Directions for Using the Magnet: The magnet is on the interior edge of the Smart Bench Block. After you punch a pin, lightly move the block around on your work surface to ensure that the pin contacts the magnetized edge. The Universal Smart Bench Block is a tool that any gun owner looking to do minor to major work on their firearm will be happy to have. Made from engineering-grade resin, this bloc... [Read More]
This flip-up front sight from Midwest Industries uses a super smooth ball bearing pivot detent that automatically locks in the raised position with a locking detent. This model is to be used with gas block height rails and folds to the front.
The Geissele gas block pin punch set is made specifically for the removal and installation of the 0.078" roll pin that secures the gas tube to the gas block of an AR-15/AR-10. Removal of a rusted-in gas block roll pin has always been a challenge since there are no commercial pin punches in 0.078" diameter. Additionally, 1/16" (0.062") punches have a tendency to bend and very few Starter punches are available in 1/16" diameter. The Geissele gas block pin punch set makes gas block work a whole lot easier. The first punch to grab when removing the roll pin is the Starter punch. This is the punch ... [Read More]
Tactical Combo Of Front And Rear Aluminum Iron Sights. • Quick Detachable Front Sight with Adjustable A2 Square Post Assembly to Fit All Picatinny/Weaver Style Rails • Equipped with Locking Retention Thumb Nut andClever and Robust Flip-up Posi-lock Design to Guarantee Zero in the Most Extreme Combat Condition • Precision Elevation Adjustments to Enhance Shooting Accuracy • Profile Designed for Installation on Gas Block • Integral Picatinny Mounting Deck to Fit All Flat Tops • Dual Aiming Apertures for All Shooting Requirements • Precision Windage Adjustments • Clever and Robust... [Read More]
The Wheeler Engineering Universal Barrel Clamp is precision extruded from aircraft grade aluminum and bonded with non-marring urethane. The urethane coating is specially designed to provide a protective layer for the barrel's finish while providing extraordinary gripping abilities. Three different barrel openings of.85",.66" and.53" will accommodate anything from a tactical rifle pencil barrel up to a bull barrel. When inserted in a vise the urethane coating squeezes down tightly on the barrel to fully secure it for the forces needed for installation/ removal.
Holland Electronics GRB-AR Grounding Block offers the ultimate protection for Cable, Satellite, Off-Air, and any other system utilizing the 5-2150MHz range. Features: Gas Tube Protection Frequency Range: 5-2150MHz Wall Mount
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com