PlasticBonder is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fiber composites, thermoplastics, coated metals, concrete & more. PlasticBonder has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, PlasticBonder sets black in color and cures to a hard, permanent bond.
The Versachem Plastic Tank and Radiator Repair Kit permanently repairs gasoline and diesel fuel tank leaks in less than 20 minutes. Use it to repair pinholes, rust-outs, hairline cracks and holes up to 1/2" in diameter. Resistant to water, gasoline, diesel and kerosene. No tank removal necessary. Have the repair ready before mixing the hardener and resin together, so that you can begin repair as soon as the pouch contents are thoroughly mixed. Heat is generated while the epoxy mixture cures. Works best on metal and plastic tanks, fuel tanks, and oil pans. Tensile strength: 1500 PSI; temperatur... [Read More]
Permatex's Permapoxy Black Plastic Weld is a structural adhesive designed for general purpose bonding of a wide variety of materials. Black Plastic Weld forms a tough, durable bond to most plastics, composites, ceramics, and wood in any combination. It is a fast-curing product with gelling of mixed adhesive in 5 to 6 minutes and fixturing in 9 to 10 minutes. Bonds hard and soft plastics to specified surfaces, and requires no primers. Sets in five minutes at room temperature, with a temperature range of -60 degrees Fahrenheit to 250 degrees Fahrenheit (-51C to 121C). Permanent strength up to 35... [Read More]
WaterWeld will plug or seal leaks and patch holes and cracks in almost anything. Ideal for repairing plumbing, fuel tanks, tub and shower, drains, pool and spa, boats and potable water tanks; setup occurs even under water. After curing, it can be drilled, tapped, filed, sanded and painted. WaterWeld has a set time of 15-25 minutes and sets hard in one hour. WaterWeld cures to an off-white color, is rated at a tensile strength of 900 PSI and will withstand temperatures up to 300ºF.
HighHeat is a hand mixable epoxy putty stick specifically formulated to bond and repair materials that will be exposed to high temperatures in automotive and industrial maintenance applications. It cures to a tough, hard bond with little to no shrinkage. This industrial-strength product outperforms conventional epoxy putties at high temperatures and sets in 1 hour at room temperature. After 8 hours, it can be drilled, tapped, machined, ground, filed and painted. HighHeat is rated at a tensile strength of 800 PSI and cures to a machine grey in color. It is able to withstand continuous heat... [Read More]
J-B MarineWeld is a specially formulated two-part epoxy cold weld system that provides for strong, lasting repairs for bonding different or similar surfaces, such as aluminum, metal, composites, fiberglass and others. MarineWeld sets in 4-6 hours at room temperature and is fully cured to a dark grey color in 15-24 hours. Once cured, it can be shaped, tapped, filed, sanded and drilled and will retain its strength above or below the waters’ surface. MarineWeld has a 1:1 mixing ratio and tensile strength of 3960 PSI.
SteelStik is a hand-mixable, steel-reinforced, non-rusting epoxy putty that quickly repairs or rebuilds anything made of metal. After mixing, it forms an industrial-strength polymer compound that can be molded into shapes or used to build up, patch and repair steel components. SteelStik sets in 3-5 minutes and after 60 minutes, can be drilled, tapped, machined, ground, filed and painted. SteelStik cures to a dark grey color, is rated at a tensile strength of 900 PSI and will withstand temperatures up to 300ºF.
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey color. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured.
CarGo QuikSteel plastic repair tank repair kit gives you everything you need to repair plastic fuel tanks, radiators, water tanks, RV holding tanks. No need to remove tank or drain, can make permanent repair in minutes.
PlasticWeld is a hand-mixable, fast-setting epoxy putty that forms a durable bond to most major plastic types. *After mixing, it forms a polymer compound that can be molded or used to build up and repair just about anything made from plastic. When cured, it can be sawed, drilled, carved, sanded and painted. PlasticWeld has a 20-25 minute work life; functional cure occurs in 2-3 hours. PlasticWeld cures to an off-white color, is rated at a tensile strength of 350 PSI. Does not adhere to polyethylene, polypropylene or some other plastics. Test for adhesion first.
This epoxy putty will plug holes and make permanent repairs in moist-surface or under water applications, Will even repair leaking fuel tanks, Simply pull off the amount of Waterweld necessary for the job, knead it with your fingers until the two colors are thoroughly mixed, then push the product into the hole, Will fully cure in 20-30 minutes, Can be drilled, sanded, filed, tapped, machined, and painted, Nontoxic and approved by the National Sanitation Foundation for use with potable water, 300 F maximum intermittent temperature, 250 F maximum continuous temperature, 1000 psi lap shear tensil... [Read More]
A two-component epoxy formula highly concentrated with carefully selected pure aluminum particles, modified curing agents and special high quality additives to provide maximum strength, durability and ease of application. Alum bond is aluminum filled epoxy specially formulated for repairing condenser coils, tanks, valves, pumps, castings, water jackets, radiators, etc., where non-rusting, non-magnetic aluminum finish is desired.
J-B KwikWeld is a fast setting version of The Original J-B Weld two-part epoxy cold weld system that provides strong, lasting repairs to metal and multiple other surface types. After mixing, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. J-B KwikWeld has a 1:1 mixing ratio, sets in 6 minutes and is fully cured in 4-6 hours. J-B KwikWeld cures to a dark grey color, is rated at a tensile strength of 2424 PSI and will withstand temperatures up to 300ºF.
Do you need to fix something? (ANYthing?) Automotive trim and parts, plastic, metals, glass, wood, concrete or rubber? TV remotes, shoes, chairs, tools, kitchen appliances? AND you need it to dry instantly right? Pratley's Powda Bond is your answer. Benefits: Powda Bond is: An instant repair, ultra fast curing adhesive kit and gap filler which can be used either as a two part kit or single adhesive. The repair kit includes: 20ml Adhesive (Special Grade Super Glue) that can be used on its own or with the filling powder(s) and 15ml each filling powder in black and white which can be mixed to ... [Read More]
Do minor repairs around the house yourself with Devcon Plastic Welder Epoxy. Its quick-drying formula cures in just 15 minutes for a fast and tight hold. Devcon plastic epoxy can bond hard plastic, ceramic, vinyl
J-B Weld PlasticWeld SyringePlasticWeld is a specially formulated two-part adhesive and epoxy filler system that provides for strong, lasting repairs. PlasticWeld will bond a variety of surfaces, such as metal, composites, fiberglass and others. PlasticWeld
Loctite, 2 Gram, Super Glue Plastic Bonder Glue, A 2 Part Cyanoacrylate Adhesive That Sets In Seconds & Develops Tremendous Strength With Just 1 Drop, Activator Primes Hard To Bond Surfaces Such As Polypropylene &
Hardens steel in 20 minutes. For use on plumbing, underwater, bathroom, auto, electrical and most any place in the home. Stops leaks, easy mix, makes repairs fast. Plugs, seals, mends, patches and is non-toxic. Patches
It comes to you in New and Fresh state,From USA 25 ML Syringe; Plastic Steel Epoxy; Steel Filled Heavy Duty Epoxy; High Bond Strength; 2;500 PSI; Slow Setting Formula For Extra Working Time; Fills Gaps
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com