Elegoo Inc. is a professional manufacturer and exporter that is concerned with the design, development production and marketing of arduino, 3d printers, raspberry pi and STM32. Our Dream is to make the best price and best quality produce for customers. So we would like to receive your valuable suggestions for our products and we can improve them for you. Features: - A, B, C, D four-phase LED indicates the status of the stepper motor work. - Stepper motor with a standard interface, when used directly pluggable. - 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 p... [Read More]
Features: 1. to 4 bidirectional DC motors and 4 PWM speed controllers (approximately 0.5% resolution) 2. Up to 2 stepper motor forward and reverse control, single / double step control, staggered or micro-step and rotation angle control 3. 4-way H-bridge: The L293D chip provides 0.6A (peak 1.2A) current per bridge with thermal shutdown protection, 4.5Vto36V 4. The pull-down resistor ensures that the motor remains stopped at power-up 5. Large terminal blocks make wiring easier (10-22AWG) and power 6. With reset button 7. 2 large terminal external power terminals, to ensure logic and motor drive... [Read More]
Technical Parameters: Voltage: DC5-10V power supply Communication Interface: IIC 16-way steering gear control Size:25*61mm Product features: The PCA9685 chip is wrapped in the center of the board Power input terminal Green power indicator In the 4 groups of 3-pin connector to facilitate the insertion of 16 servo motor (servo motor plug slightly wider than 0.1 ") The polarity of the reverse polarity is input on the terminal block Cascade design: V + line to place a large capacitor, the maximum external input voltage depends on the 10V 1000uf capacitor All PWM output lines have a 220 ohm series ... [Read More]
This controller is able to regulate the speed of one DC motor with Arduino. Cytron 10A Motor Driver Shield (Arduino)"SHIELD-MD10" is a compatible Arduino motor shield for controlling high current brushed DC motor up to 10A continuously. It should be stacked on to an Arduino main controller board such as Arduino UNO R3. Features: Shield for Arduino Speed controller to control one motor. Bi-directional control for 1 brushed DC motor. Support motor voltage ranges from 7V to 30V (Rev2.0). Maximum current up to 10A continuous and 15A peak (10 seconds). 3.3V and 5V logic level input. Solid state ... [Read More]
L9110S H-bridge Dual DC Stepper Motor Driver Controller Board for Arduino Description: Dual motor driver chip L9110S Module supply voltage :2.5-12V Suitable motor Range: between the motor operating voltage 2.5v-12V, the maximum operating current 0.8A, voltage and current smart car currently available in the market are within this range Can drive two DC motors , or a 4-wire 2 -phase stepper motor. PCB size : 2.8cm * 2.1cm ultra- small size, suitable for assembly A fixed mounting hole diameter : 3mm 6P black bent pin description External 2.5V-12V voltage VCC External GND GND IA1 exter... [Read More]
Instruction:This driver uses Infineon chips BTS7960 composed of high-power drive full H-bridge driver module with thermal over-current protection. Double BTS7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High-current 43A.Electrical performance:Model: IBT-2Input voltage: 6V-27VMaximum current: 43AInput level: 3.3-5VControl method: PWM or levelDuty cycle: 0-100%Input port:1.RPWM: forward level or PWM signal input, active high2.LPWM: Reverse level or PWM signal input, active high3.R_EN: forward drive enable input, high-le... [Read More]
L298N is a kind of high voltage,high current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V),large output current(instantaneous peak current up to 3A,continuous working current 2A) and 25W of rated power.Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor,relay coil and so on.Using standard logic level signal control,it has two enable control ends.It permits or prohibites device having a logic power supply input without the ... [Read More]
Overview: Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A. Use eight high-speed Schottky diodes at motor output as protection. Stack design can be directly plugged into the Arduino, easier to use. The L298P shield DC motor driver has PWM speed control mode; dual high-power H-bridge driver. Features: 1, the board with L 2 9 8 P motor drive chip, directly with the motherboard digital I O port (D10, D11, D12, D13), without cumbersome wiring. 2, onboard buzzer (D4), you can set the reverse alarm ringtones. 3, convenient motor ... [Read More]
Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage,high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals.The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the con-nection of an external sensing resistor... [Read More]
Get your Arduino moving! This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. These great drivers also offer current-sense feedback and accept ultrasonic PWM frequencies for quieter operation. The Arduino pin mappings can all be customized if the defaults are not convenient, and the motor driver control lines are broken out along the left... [Read More]
DROK 12v 24v 36v DC Brush Motor Controller Parameters: Output channel: 2-way Working voltage: 5-36V 2 channel max current: 16A Each channel rated current: 8A Each channel output rated power: 96W (12V input); 288W (36V input). Control signal voltage:3-5V Each channel control signal current: 2-10MA Support PWM frequency range: 2-20K Support PWM duty ratio range: 0-99% Min. PWM effective pulse width: 10US Working temperature:-10℃-80℃ Notes: 1. We recommend adding the fuses, as without fuses on the power supply circuit of the motherboard. The reversed connection will cause some of the chip... [Read More]
L298N of TIMESETL TIMESETL Motor Drive Controller - High Quality Specification: Size: 43*43*27mm/ 1.69*1.69*1.06 inch Dual H bridge drive (can drive 2 DC motors) Chip: L298N Logical voltage: 5V Drive voltage: 5V-35V Logic current: 0mA-36mA Drive current: 2A(For each DC motor) Weight: 30g TIMESETL L298N DC Stepper Motor Drive - Usage Great for Arduino, Smart Car, Power UNO, MEGA R3, Mega 2560, etc If driving voltage is more than 12V, please use external 5volt logic outputs to switch the H-bridge circuits. Delivery 5 x L298N Stepper Motor Controller
CNC Expansion Board:-GRBL 0.9 compatible-Runs on 12-36V DC -4-Axis support: X, Y, Z-It can drive 4 stepper motors, and each stepper motor only needs 2 IO ports. That is to say, 6 IO ports can manage 3 stepper motors very well, which is very convenient to use.KeeYees UNO R3 Board: -Microcontroller: ATmega328P-Chip: ATmega16U2 -Operating Voltage: 5V-Input Voltage (recommended):7-12V-Input Voltage (limit):6-20V-Flash Memory: 32 KB of which 0.5 KB used by bootloader-Digital I/O Pins: 14 Digital I/O Pins (6 PWM outputs)-Analog Input Pins: 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 m... [Read More]
Description: The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW- CCW- short- brake - and stop. The two motor outputs (A and B) can be separately controlled- the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz... The STBY pin should be pulled high to take the motor out of standby mode. Logic supply voltage (VCC) can be in the range of 2.7-5.5VDC- while the motor supply (VM) is limited to a maximum voltage of... [Read More]
CNC Shield Board: Latest CNC Shield Version 3.0 for arduino. GRBL 0.9 compatible. 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). Support 6pcs ends stop for each axis. Coolant enable. Compatible with A4988 or DRV8825 stepper driver. Runs on 12-36V DC. DRV8825 Stepper Motor Driver: Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It's not arduino official board but it's compatible with all arduino software and hardware). Nema 17 Stepper motor Specification: Model No.:17HD48002H-22B Step Angle: 1.8 deg Holdi... [Read More]
Features:- Brand new and high quality.- Different from other kits,it adds some functional modules(such as RFID, temperature and humidity module.).- Suitable for Arduino enthusiasts. - Make you enjoy arduino world in a gradual way.- Super
Package Included:1 x Tank Robot ChassisSpecifications:Size: wide 9.7cm* long 18.5cm* high 5cmVoltage: 3-7VMotors: 130Weight: 166gFeatures:1. Only 166g in weight2. Good damping effect, you can press down to 0.7cm3. With general motors 130, support 3-7V voltage
Package Included:1 x Tank Robot ChassisSpecifications:Size: wide 9.7cm* long 18.5cm* high 5cmVoltage: 3-7VMotors: 130Weight: 166gFeatures:1. Only 166g in weight2. Good damping effect, you can press down to 0.7cm3. With general motors 130, support 3-7V voltage
Features:Built-in PWM drive and a clock.Adopts IIC interface for communication.With LED light to indicate connection status.Includes reverse polarity protection on the input board.Adjustable frequency PWM up to about 1.6 KHz.Can output 12 bit resolution for
Features:Built-in PWM drive and a clock.Adopts IIC interface for communication.With LED light to indicate connection status.Includes reverse polarity protection on the input board.Adjustable frequency PWM up to about 1.6 KHz.Can output 12 bit resolution for
Please note, this item ships from an international seller. Expected delivery is 10-15 days. International ShippingL298P Shield DC motor driver adopts the L298P driver chip wich is exclusively made for large-power motor. It can drive
DescriptionThe DRV8825 stepper motor driver carrier is a breakout board for TIs DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper
L298P Shield DC motor driver adopts the L298P driver chip wich is exclusively made for large-power motor. It can drive 2 DC motors directly with a drive current reaching 2A. The motor output is equipped
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com