The Wheeler Engineering Scope Mounting Kit Combo 1-inch/30mm is a complete scope mounting kit that provides everything necessary to mount a scope the correct way. Proper scope installation is critical to the accuracy of your firearm. Get the most accuracy possible out of your gun by ensuring proper scope installation. The Wheeler Alignment Bars, Lapping Bars and Lapping Compound allow you to achieve the perfect fit between scope and rings. Securing Fasteners properly is critical to accuracy as well. Precisely controlled torque along with thread locking compound will keep your scope held secure... [Read More]
This kit improves scope mounting two ways. First, the short bars let you know when the front ring is in perfect alignment with the rear one. Second, lapping the inside of the scope rings will reduce or eliminate any shifting of the scope inside the rings and will also remove machining marks that can scratch the finish on the scope. This is "State-of-the-Art" scope mounting and will provide you with confidence that the job has been done right. The kit included 2 alignment rods, lapping rod with handle (8" steel shaft, plastic ball handle) and 1 oz. jar of 220 grit high quality silicon carbide l... [Read More]
Mounting to a Pica tinny or Weaver type rail, the standard, 2-screw Hunter rings are a nice match for general hunting setups. Made from aircraft-grade 6061-T6 aluminum for optimum strength.
Features: Fits all .22/Airgun rail and some rifles, such as Henry 22LR, Marlin model 60 70, Marlin 995, Air pistols and so on. But not for AR rifle. (for a flat rail) Features in high profile, one of the ring mounts design with removable stop pin, provide solid mounting on the rail. The ring is for most scopes which are in 1''/ 25.4mm scope tube. Precision machining from aircraft-grade aluminum alloy, solid and sturdy construction. Built-in tape inside per rings to prevent from marring the scope, also prevent sliding and holding postion accurately. With two rail clamp screws and two scope cla... [Read More]
The Monstrum Tactical Offset Dual Ring Picatinny Scope Mount is built to mount standard 1 inch tube scopes to any standard Picatinny rail equipped rifle. The offset design provides an additional 2 inches of forward extension, allowing extra flexibility for optimum eye relief and shooting position. The mount is 5.75 inches in total length. The base is 3 inches long with the mounting bolts spaced 2 inches apart, a minimum of 3 inches of rail space is required to install. The height between the top of the base to the bottom of the scope rings is 1 inch, providing 1 inch of vertical clearance. The... [Read More]
Fits 20mm Picatinny Weaver rails, Flat Top Dual Ring Scope Mount for Vortex, Nikon, Leupold and other scopes, ar-pep Front ring top and both side feature picatinny for mounting laser flashlight and compact red dot and so on accessories.- 1" Rings Heavy duty - will hold up under heavy recoil sustained fire in the most extreme circumstances. Easy installation with minimal effort over the Barrel and the cleaning rod PEPR Proper eye position ready for combat riflescopes, mount provides 2" of forward scope positioning on the .223 flat top platform. Riser Mount for Rifles with Picatinny/Weaver Rail,... [Read More]
The simplest, most accurate scope leveling system ever devised. Misaligned crosshairs Rob you of accurate bullet placement, especially at long range, where it counts. Crooked crosshairs cause your scope adjustments to be unreliable, and even make zeroing your rifle a frustrating and costly experience. The level-level-level works because the scope is leveled to your receiver, not to the top of a scope base. The makers of some scope leveling devices tell you that leveling your scope to the top of the base produces a level scope. Don't believe it! an accurate rifle requires level crosshairs, and ... [Read More]
Designed to maximize accuracy, our bubble level makes it easy to maintain a perfect horizontal hold during extreme-range shooting. Available for 35mm, 34mm, 30mm, and 1-inch riflescope tubes.
The Monstrum Tactical 1" Scope Ring Set is designed for mounting standard 1" tube rifle scopes. The rings mount to any flat top Picatinny or Weaver rail equipped rifle. High profile in height, it measures 0.7 inches from the base of the mount to the bottom of the rings. A see through channel at the base of the rings allows for simultaneous use of low profile front sights. Constructed from aerospace aluminum, the rings are both lightweight and durable.
Wheeler's FAT Wrench brings perfect consistency to every screw on your rifle! This amazing handheld torque wrench lets you apply repeatable, accurate torque settings to scope rings, guard screws and other screws, which aids in accuracy and decreases the opportunity for problems in the field. The FAT Wrench is a perfect complement to the Deluxe Gunsmithing Screwdriver Sets. Together, they can ensure accurate tightening of most every screw on any gun in your collection.
1inch / 30mm Forward reach 1 Piece Rifle Scope Mount Airsoft One Piece Torch Mount with quick release Fits 20mm Weaver rails Comes with 25.4mm reducer inserts so you can use this with 30mm and 25 mm (1 inch) body tube rifle scopes. Built in Weaver style rails - very handy fitting flashlights and lasers etc. Front Lens Size: Up to 56mm - This figure describes the maximum size of the objective (front) lens. Reach Forward / Backward Design. Clamp Design: Triple Clamp (6 bolts on each cap) Finished in Tactical Matt Black. Measurements: The Overall length = 13.5cm Height from Rail to top of scope r... [Read More]
Features: ✪Fits all 21mm picatinny and weaver rails. ✪The ring is for most scopes which are in 1''/ 25.4mm scope tube. ✪Precision machining from aircraft-grade aluminum alloy, solid and sturdy construction. ✪Built-in tape inside per rings to prevent from marring the scope, also prevent sliding and holding postion accurately. ✪With only 1 rail clamp screw and 1 scope clamp screw per side, just twist off the nut and mount the base on the 20mm rail easily. ✪Precision and Repeatable Alignment. Specification: Rail Type: 20mm Weaver/ Picatinny Rails Ring Diameter: 1'' Materia... [Read More]
The Monstrum Tactical Lockdown Scope Ring Series is our most rugged and heavy duty optic mounting system yet! The extra wide design - 1 inch in width with 6 torx locking screws per ring - provide for maximum lockdown and performance. Built to mount heavy duty optics and to withstand heavy duty rounds, the Monstrum Tactical Lockdown Series is guaranteed to hold zero against the heaviest of recoil! 1 inch in diameter, the rings are built for use with standard 1 inch scope tubes. The Picatinny base is compatible with all Picatinny mounting systems. The torx locking screw system allows for quick... [Read More]
This cantilever scope mount has inserts to accommodate both 30mm and 25mm (1") rifle scope diameters. It features a bubble level on the rear of the scope to ensure complete accuracy. Includes: 1 Cantilever Mount
The TRINITY 4X32 Compact Mil-Dot Scope w/ Rings offers superb light transmission thanks to its blue fused multi -coated lenses, which reduce internal reflections and also provide protection against scratches. The TRINITY 4x32 Compact Scope
The Monstrum Tactical 1" Scope Ring Set is designed for mounting standard 1" tube rifle scopes. The rings mount to any flat top Picatinny or Weaver rail equipped rifle. Medium profile in height, it measures
Features/Specifications: Double hex screws to hold your scope firmly in place. 9-11mm models are fitted with a recoil stop pin. Reversible dove tail clamp that fits 9-11mm and 3/8 inch. Internal cusion tape prevents markings
Light weight rifle scope is designed for fast and accurate target acquisition Ideal for target shooting, small game or vermin hunting. Fast and accurate target acquisition. Simple design, easy to use, ideal for beginners and
Features: Weighs 2.6 ounces, Length: 5 inches, Rail width: 7/8 inches, Fits most Mil-Spec H&k MP-5, GSG-5, Hk-94, G3, PTR-91 Cetme and similar clones, Material: Durable aluminum, Weaver base rail allows for any scope rings
New generation See Through design One piece body design for better scope alignment Good for use with both 30mm and 1inch scopes 1.58" (40mm) optimal center height for flat top Made of aircraft grade aluminum
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com