The Edelbrock Performer Intake Manifold delivers superior performance with square-bore carburetors. Horsepower gains from idle to 5, 500 RPM, when used with Performer Series square-bore or Thunder Series AVS carburetors. Dyno tests show that the power gains an extra 5 horsepower, 9 foot / pounds and torque across the entire RPM range over their own performer manifolds.
Intake ManifoldSmall Block Chevy with 1996-Up Vortec L31 Cast Iron HeadSquare Bore (non-EGR)Idle to 5500 RPMCast Aluminum Port exit dimensions: 1.04" x 2.03"Recommended Intake Gasket: JEGS p/n 555-210003Estimated runner length - Shortest: 4.00"Estimated runner length - Longest: 6.50"Manifold height: (A) 4.13", (B) 5.21"Click here to determine carburetor pad height.May also be used on Vortec or 1995-Earlier blocks with Vortec pattern cylinder headsAccepts late model alternator, water neck, AC, and HEINo provision for divorced or heated chokeStock/stamped steel valve covers may require 3/16" (or... [Read More]
Set of 12 Small Block Chevy Intake Manifold Bolts This bolt kit fastens the intake manifold to the cylinder heads Fits: SBC engines up to 1997 (including LT1) Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum Includes 12 bolts 3/8" Standard Thread
The Edelbrock Performer RPM Air-Gap Intake Manifold is manufactured from aluminum and given a natural finish. The exclusive Air-Gap design features an open space between the intake runners and the hot engine oil resulting in a cooler, denser charge and more power. The runners are tuned up to move the power band 1, 000 RPM higher than Performer Air-Gap manifolds, from idle-5, 500 RPM up to 1, 500-6, 500 RPM. It also features nitrous bosses, rear water outlets and two distributor clamp locations.
If you're building a high-performance Small Block Fits Chevy on a budget, then this is the intake manifold for you! The Speedway Hi-Rise aluminum intake is a dual plane, 180° street manifold designed to be used with Holley, Carter AFB or Edelbrock square flange carbs. Fits 1957-86 S/B Fits Chevy engine applications. Power range is 1500-6500 RPM Larger-than-stock plenum and runners complements other upgrades Supports larger engines & enhances RPM potential Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane Dual distributor hold-downs Accepts ... [Read More]
This is a new satin aluminum high rise single plane intake for small block Chevy. Big power for mid to upper RPM ranges! Ideal for high performance and race applications. These intakes are produced from steel molds to reduce core shift, have all the major features found on the expensive ones such as 4 corner water outlets and nitrous bosses, and the best part - the price! Intake works with 283-400 small blocks up to 1995. Does not fit the newer Vortec heads. For use with square bore style carbs. Provides standard bosses and tapped holes for street accessories such as A/C and alternator bracket... [Read More]
This is a new satin aluminum dual plane intake for small block Chevys with Vortec heads. 180° design for power over a wide RPM range. Ideal for everyday to moderate street performance applications, produces best power from idle to 5500 RPM. Designed to fit '96 and later engines and early motors with the Vortec head swap. These intakes are produced from steel molds to reduce core shift and are 100% pressure tested to insure leak free operation. They also have all the major features found on the expensive ones such as 4 corner water outlets, dual distributor hold downs, external water bypass pr... [Read More]
This is a new satin aluminum dual plane intake for small block Chevy. 180° high rise design, big power over a wide RPM range. Ideal for everyday to high performance street applications, will produce power in the lower RPM range and not kill your bottom end like a single plane would. Intake works with 283-400 small blocks up to 1995. Includes special adapter bushings for the middle holes on the '87 to '95 heads. Does not fit the newer Vortec heads. For use with square bore style carbs. Provides standard bosses and tapped holes for street accessories, accepts late model wateneck, A/C and altern... [Read More]
Intake Manifold1955-1986 Small Block Chevy 265-283-302-327-350-400Square Bore (non-EGR)Idle to 5500 RPMCast Aluminum Port exit dimensions: 1.17" x 1.90"Recommended Intake Gasket For Apps without Heat cross over use JEGS p/n 555-210002Recommended Intake Gasket For Apps with Heat cross over use JEGS p/n 555-210004Estimated runner length - Shortest: 4.00"Estimated runner length - Longest: 7.00"Manifold height: (A) 4.29", (B) 5.31"Click here to determine carburetor pad height.Also Fits 1987-Up stock aluminum heads (does not fit 1987-Up cast iron or Chevrolet Bow Tie heads)Accepts late model chok... [Read More]
In our opinion these are not $400.00 show quality polished intakes. Flaws in the polish such as scuffs and marks will require more polishing to enhance the finish. This is a new polished aluminum dual plane intake for small block Chevy. 180° high rise design, big power over a wide RPM range. Has the open air area under the carb pad to help keep fuel mixture cool and improve power. Ideal for everyday to high performance street applications, will produce power in the lower RPM range and not kill your bottom end like a single plane would. These intakes are produced from steel molds to reduce cor... [Read More]
This Fel-Pro intake manifold gasket set is ideal for rebuilds and mild performance engines or as an OEM stock replacement. For stock port engines and carries a one year manufactures warranty.
Give Your Small Block Chevy Engine a new look with our 205 Piece Stainless Steel Hex Bolt kit!! Our special intake washers are 1/8 thick. The bolts in this kit are made from 304 stainless steel. This Bolt Kit Fits All 265, 283, 302, 305, 307, 327, 350 , and 400 Chevy Engines.(Non-EFI). This is a complete high quality stainless steel hex bolt kit. The kit includes individually packaged and labeled component kits for the following items: Intake Manifold- Timing Cover- Water Pump- Oil Pan- Thermostat Housing- Distributor- Coil Bracket- Fuel Pump- Valve Covers- Headers- Crank Pulley- Fan Pulley - ... [Read More]
This Listing is for a new pair of # P1205 intake gaskets as shown compatible with small block Chevy Fel-Pro BULK . Not skin packed. Gaskets Only! For '55-'00 262-400 engines. Famous Fel-Pro quality, great for stock to high performance rebuilds. Printoseal design with elastomer beads around the ports for extra sealing. Gaskets are .060" Thick and Port hole size 1.28" x 2.09" with no exhaust crossover.
Replaces existing Fuel Petcock, Just replace and ride again. Give your machine the new power and torque it really deserves, and have more fun with the power at your finger tips. Petcock Replaces OEM Number:
Fitment:2004 Yamaha Warrior 350 YFM350X2003 Yamaha Warrior 350 YFM350X2002 Yamaha Warrior 350 YFM350X2001 Yamaha Warrior 350 YFM350X2000 Yamaha Warrior 350 YFM350X1999 Yamaha Warrior 350 YFM350X1998 Yamaha Warrior 350 YFM350X1997 Yamaha Warrior 350 YFM350X1996 Yamaha Warrior
A damaged intake manifold is a serious problem that can lead to expensive repairs. Symptoms such as vacuum leaks, coolant leaks can lead to all sorts of problems such as misfires to overheating. Replacing them
A damaged intake manifold is a serious problem that can lead to expensive repairs. Symptoms such as vacuum leaks, coolant leaks can lead to all sorts of problems such as misfires to overheating. Replacing them
Intake ManifoldSmall Block Chevy with 1996-Up Vortec L31 Cast Iron HeadSquare Bore (non-EGR)Idle to 5500 RPMCast Aluminum Port exit dimensions: 1.04" x 2.03"Recommended Intake Gasket: JEGS p/n 555-210003Estimated runner length - Shortest: 4.00"Estimated runner length
© 10Toply.com - all rights reserved - Sitemap 10Toply.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com